RF SYSTEM
  Home Page » Catalogo » KENWOOD ricambi compatibili » 0061 Il mio account  |  Cosa c'è nel carrello  |  Acquista   
Categorie
Cavi PTT-> (17)
Componenti (2)
ICOM ricambi compatibili (3)
Interfaccia TinyGate
KENWOOD ricambi compatibili-> (34)
  TL922 amplificatore (1)
  TS850 (4)
  TS870 (4)
  TS930 (3)
  TS940 (4)
Ricevitore SDR-> (2)
YAESU ricambi compatibili (4)
Produttori
Novità Altro
Cavo PTT con relè per amplificatore per ICOM IC7300
Cavo PTT con relè per amplificatore per ICOM IC7300
39.00EUR
Ricerca veloce
 
Usa parole chiave per trovare il prodotto
Ricerca avanzata
Informazioni
Rivenditori
Spedizioni e Consegna
Privacy
Condizioni di vendita
Contattaci
Impressum
CRuni-NG riferimento ad alta stabilità di frequenza per trx ICOM
[0061]
82.96EUR

The CRuni-NG is a programmable high stability synthesizer unit, based on a Si5351 CMOS synthesizer with a high stability TCXO as reference clock.
It's designed as a replacement for many ICOM's OCXO crystal units, like the ICOM CR338, CR282 and CR293 OCXO crystal units.


This board can be used in many ICOM transceivers, but as a programmable unit it's virtually compatible with many other radios.


For more technical detail see: CRuni-NG Project webpage

The CRuni-NG has the same dimension, pin assignment and location as the CR338 and CR282, so it's mechanically and electrically 100% compatible with both units. The compatibility with the CR293 are given through an adapter board (see options below):



How to install in a ICOM IC910H: CRuni-NG IC910H installation notes

Even the fine frequency calibration by the transceiver is still possible with the CRuni-NG, except on models IC761 and IC765.
Please note: We don't recommend to order the 0,05ppm stability option for IC761, IC765, IC738 or IC736!
Another important feature of the CRuni-NG is the high quality multiturn trimmer, which permit a fine frequency alignment from the top without removing the unit from the transceiver.
The high quality TCXO from JAUCH QUARTZ used on this module providing a high degree of frequency stability over a wide temperature range and very low spure levels. Furthermore there are no warm-up delays like with the orginal OCXO units, because no heater are necessary for a TCXO (Temperature Compensated Crystal Oscillator)
The board is delivered as full assembled and tested, so is it quite easy for most people with soldering skills to install and/or replace the original CRxxx unit in the transceiver.


The specifications:

- Output frequency: 30MHz, 30.2MHz or 32MHz (programmable for any value from 8kHz up to 160 MHz)
- Output level: LVCMOS, AC-coupled
- Output Frequency stability: ±0,42ppm@30MHz (or ±0,08ppm@30MHz with extra high stability option: ±0,05ppm)
- Reference TCXO Frequency stability: ±0,28ppm@20MHz (or with extra high stability option: ±0,05ppm)
- Operating Temperature Range: -20 to 70°C
- Frequency fine adjustment range: 90Hz (±5ppm) (or with extra high stability option: 100Hz)
- Power supply requirements: 4,5 to 28 VDC, max. 60mA (or with extra high stability option: 4,5 to 12 VDC, max. 89mA)
- Module size (LxWxH): 25x15x13mm

Each CRuni-NG is shipped as tested in our lab with a Rubidium frequency standard.

We provide the CRuni-NG with some different frequencies and/or adapter module options, so choose please your right option here below:

Opzioni disponibili:
Frequenza:
Opzione stabilità:
Per ulteriori informazioni, visita il sito.
Questo prodotto è stato aggiunto al nostro catalogo il marted́ 21 febbraio, 2023.
Recensioni
I clienti che hanno questo preso quest prodotto lo hanno anche comprato?????
SUB-TUNE Encoder per YAESU FT847
SUB-TUNE Encoder per YAESU FT847
MEM/VFO CH Encoder per YAESU FT847
MEM/VFO CH Encoder per YAESU FT847
Carrello Altro
0 prodotti ...è vuoto
Lingue
English Deutsch Italiano
Info sul produttore
Altri prodotti
Comunicazioni Altro
ComunicazioniComunica gli aggiornamenti diCRuni-NG riferimento ad alta stabilità di frequenza per trx ICOM
Valute

Copyright © 2024 RF SYSTEM
Powered by osCommerce