RF SYSTEM
  Home Page » Catalogo » KENWOOD ricambi compatibili » 0061 Il mio account  |  Cosa c'è nel carrello  |  Acquista   
Categorie
Cavi PTT-> (16)
Componenti (2)
ICOM ricambi compatibili (3)
Interfaccia TinyGate
KENWOOD ricambi compatibili-> (33)
  TL922 amplificatore (1)
  TS850 (4)
  TS870 (4)
  TS930 (3)
  TS940 (4)
Ricevitore SDR-> (2)
YAESU ricambi compatibili (4)
Produttori
Novità Altro
Cavo PTT per amplificatore per ICOM (spina DIN a 8 pin)
Cavo PTT per amplificatore per ICOM (spina DIN a 8 pin)
25.00EUR
Ricerca veloce
 
Usa parole chiave per trovare il prodotto
Ricerca avanzata
Informazioni
Rivenditori
Spedizioni e Consegna
Privacy
Condizioni di vendita
Contattaci
Impressum
CRuni-NG riferimento ad alta stabilità di frequenza per trx ICOM
[0061]
82.96EUR

The CRuni-NG is a programmable high stability synthesizer unit, based on a Si5351 CMOS synthesizer with a high stability TCXO as reference clock.
It's designed as a replacement for many ICOM's OCXO crystal units, like the ICOM CR338, CR282 and CR293 OCXO crystal units.


This board can be used in many ICOM transceivers, but as a programmable unit it's virtually compatible with many other radios.


For more technical detail see: CRuni-NG Project webpage

The CRuni-NG has the same dimension, pin assignment and location as the CR338 and CR282, so it's mechanically and electrically 100% compatible with both units. The compatibility with the CR293 are given through an adapter board (see options below):



How to install in a ICOM IC910H: CRuni-NG IC910H installation notes

Even the fine frequency calibration by the transceiver is still possible with the CRuni-NG, except on models IC761 and IC765.
Please note: We don't recommend to order the 0,05ppm stability option for IC761, IC765, IC738 or IC736!
Another important feature of the CRuni-NG is the high quality multiturn trimmer, which permit a fine frequency alignment from the top without removing the unit from the transceiver.
The high quality TCXO from JAUCH QUARTZ used on this module providing a high degree of frequency stability over a wide temperature range and very low spure levels. Furthermore there are no warm-up delays like with the orginal OCXO units, because no heater are necessary for a TCXO (Temperature Compensated Crystal Oscillator)
The board is delivered as full assembled and tested, so is it quite easy for most people with soldering skills to install and/or replace the original CRxxx unit in the transceiver.


The specifications:

- Output frequency: 30MHz, 30.2MHz or 32MHz (programmable for any value from 8kHz up to 160 MHz)
- Output level: LVCMOS, AC-coupled
- Output Frequency stability: ±0,42ppm@30MHz (or ±0,08ppm@30MHz with extra high stability option: ±0,05ppm)
- Reference TCXO Frequency stability: ±0,28ppm@20MHz (or with extra high stability option: ±0,05ppm)
- Operating Temperature Range: -20 to 70°C
- Frequency fine adjustment range: 90Hz (±5ppm) (or with extra high stability option: 100Hz)
- Power supply requirements: 4,5 to 28 VDC, max. 60mA (or with extra high stability option: 4,5 to 12 VDC, max. 89mA)
- Module size (LxWxH): 25x15x13mm

Each CRuni-NG is shipped as tested in our lab with a Rubidium frequency standard.

We provide the CRuni-NG with some different frequencies and/or adapter module options, so choose please your right option here below:

Opzioni disponibili:
Frequenza:
Opzione stabilità:
Per ulteriori informazioni, visita il sito.
Questo prodotto è stato aggiunto al nostro catalogo il marted́ 21 febbraio, 2023.
Recensioni
I clienti che hanno questo preso quest prodotto lo hanno anche comprato?????
MEM/VFO CH Encoder per YAESU FT847
MEM/VFO CH Encoder per YAESU FT847
SUB-TUNE Encoder per YAESU FT847
SUB-TUNE Encoder per YAESU FT847
Carrello Altro
0 prodotti ...è vuoto
Lingue
English Deutsch Italiano
Info sul produttore
Altri prodotti
Comunicazioni Altro
ComunicazioniComunica gli aggiornamenti diCRuni-NG riferimento ad alta stabilità di frequenza per trx ICOM
Valute

Copyright © 2024 RF SYSTEM
Powered by osCommerce